Author: Mibe, T.
Paper Title Page
MOPOST017 Design and Beam Dynamics Study of Disk-Loaded Structure for Muon Linac 94
 
  • K. Sumi, T. Iijima, K. Inami, Y. Sue, M. Yotsuzuka
    Nagoya University, Graduate School of Science, Chikusa-ku, Nagoya, Japan
  • H. Ego, T. Mibe, N. Saito, M. Yoshida
    KEK, Ibaraki, Japan
  • T. Iijima
    KMI, Nagoya, AIchi Prefecture, Japan
  • Y. Kondo, K. Moriya
    JAEA/J-PARC, Tokai-Mura, Naka-Gun, Ibaraki-Ken, Japan
  • Y. Nakazawa
    Ibaraki University, Hitachi, Ibaraki, Japan
  • M. Otani
    J-PARC, KEK & JAEA, Ibaraki-ken, Japan
  • Y. Takeuchi
    Kyushu University, Fukuoka, Japan
  • H.Y. Yasuda
    University of Tokyo, Tokyo, Japan
 
  The disk-loaded structures (DLS) in the muon LINAC are under development for the J-PARC muon g-2/EDM experiment. Four DLSs with an accelerating gradient of 20 MV/m take charge of muon acceleration from 40 MeV to 212 MeV, which corresponds to 70% to 94% of the speed of light. The quasi-constant gradient type TM01-2pi/3 mode DLSs with gradually varying disk spacing was designed and confirmed that the cumulative phase slip due to the mismatch between muon and phase velocity can be suppressed to less than 2 degrees at the frequency of 2592 MHz. In addition, the optimum synchronous phase and the lattice were investigated to satisfy the requirements of the total emittance less than 1.5 pi mm mrad and the momentum spread less than 0.1% in RMS.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2022-MOPOST017  
About • Received ※ 19 May 2022 — Revised ※ 09 June 2022 — Accepted ※ 16 June 2022 — Issue date ※ 20 June 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPOMS046 Fabrication and Low-Power Test of Disk-and-Washer Cavity for Muon Acceleration 1534
 
  • Y. Takeuchi, J. Tojo
    Kyushu University, Fukuoka, Japan
  • E. Cicek, H. Ego, K. Futatsukawa, N. Kawamura, T. Mibe, M. Otani, N. Saito, T. Yamazaki, M. Yoshida
    KEK, Ibaraki, Japan
  • Y. Iwashita
    Kyoto University, Research Reactor Institute, Osaka, Japan
  • R. Kitamura, T. Morishita
    JAEA/J-PARC, Tokai-mura, Japan
  • Y. Kondo
    JAEA, Ibaraki-ken, Japan
  • Y. Nakazawa
    Ibaraki University, Hitachi, Ibaraki, Japan
  • Y. Sue, K. Sumi, M. Yotsuzuka
    Nagoya University, Graduate School of Science, Chikusa-ku, Nagoya, Japan
  • H.Y. Yasuda
    University of Tokyo, Tokyo, Japan
 
  The muon g-2/EDM experiment is under preparation at Japan Proton Accelerator Research Complex (J-PARC), and the muon linear accelerator for the experiment is being developed. A Disk-and-Washer (DAW) cavity will be used for the medium-velocity part of the accelerator, and muons will be accelerated from v/c=ß=0.3 to 0.7 with the operating frequency of 1.296 GHz. Machining, brazing, and low-power measurements of a prototype cell reflecting the design of the first tank of DAW were performed to identify fabrication problems. Several problems were identified, such as displacement of washers during brazing, and some measures will be taken in the actual tank fabrication. In this paper, the results of the prototype cell fabrication will be reported.  
DOI • reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2022-TUPOMS046  
About • Received ※ 08 June 2022 — Revised ※ 15 June 2022 — Accepted ※ 16 June 2022 — Issue date ※ 23 June 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)