Paper |
Title |
Page |
TUPOTK063 |
CERN Linac4 Chopper Dump: Operational Experience and Future Upgrades |
1370 |
|
- C.J. Sharp, P. Andreu Muñoz, M. Calviani, G. Costa, L.S. Esposito, R. Franqueira Ximenes, D. Grenier, E. Grenier-Boley, J.R. Hunt, A.M. Krainer, C.Y. Mucher, C. Torregrosa
CERN, Meyrin, Switzerland
|
|
|
The Chopper Dump in the Linac4 accelerator at CERN is a beam-intercepting device responsible for the absorption of the 3 MeV H− ion beam produced by the Linac4 source and deflected upstream by an electromagnetic chopper. It allows a portion of the beam, which would otherwise fall into the unstable region of the radiofrequency buckets in the Proton Synchrotron Booster, to be dumped at low energy with minimal induced radiation. It may also be used to absorb the entire beam. With peak currents of 25 to 45 mA and shallow penetration, this results in large deposited energy densities, thermal gradients and mechanical stresses. Additional constraints arise from geometric integration, vacuum and radiation protection requirements. Material selection, beam-matter interaction studies and thermo-structural analyses are important aspects of the design process. The Chopper Dump underwent modification in 2019 following observed material degradation in the original version of the device. The experience gained, modifications made and observations noted since then are detailed herein. Against this background, the design and analysis of an upgraded device, intended to cope with future operational conditions, is outlined and discussed.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2022-TUPOTK063
|
|
About • |
Received ※ 20 May 2022 — Revised ※ 12 June 2022 — Accepted ※ 13 June 2022 — Issue date ※ 26 June 2022 |
Cite • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
WEPOST026 |
Conceptual Design of the FCC-ee Beam Dumping System |
1753 |
SUSPMF002 |
|
|
- A.M. Krainer, P. Andreu Muñoz, W. Bartmann, M. Calviani, Y. Dutheil, A. Lechner, F.-X. Nuiry, A. Perillo-Marcone
CERN, Meyrin, Switzerland
- R.L. Ramjiawan
JAI, Oxford, United Kingdom
|
|
|
The Future Circular electron-positron Collider (FCC-ee) will have stored beam energies of up to 20 MJ. This is a factor 100 higher than any current or past lepton collider. A safe and reliable disposal of the beam onto a beam dump block is therefore critical for operation. To ensure the survival of the dump core blocks, transversal dilution of the beam is necessary. To reduce the complexity of the system and guarantee high availability, an optimized, semi-passive beam dumping system has been designed. The main dump absorber design has been optimized following recent studies for high energy dump block materials for the LHC High Luminosity upgrade. First simulations regarding the radiation environment of the dumping system have been carried out, allowing the definition of preliminary constraints for the integration with respect to radiation sensitive equipment. The performance of the system has been evaluated using Monte-Carlo simulations as well as thermomechanical Finite-Element-Analysis to investigate potential material failure and assess safety margins. An experiment at the CERN HiRadMat facility has been carried out and preliminary results show good agreement with simulations.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2022-WEPOST026
|
|
About • |
Received ※ 07 June 2022 — Revised ※ 16 June 2022 — Accepted ※ 16 June 2022 — Issue date ※ 25 June 2022 |
Cite • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
THPOTK049 |
Irradiation of Low-Z Carbon-Based Materials with 440 GeV/c Proton Beam for High Energy & Intensity Beam Absorbers: The CERN HiRadMat-56-HED Experiment |
2883 |
|
- P. Andreu Muñoz, M. Calviani, N. Charitonidis, A. Cherif, E.M. Farina, A.M. Krainer, A. Lechner, J. Maestre, F.-X. Nuiry, R. Seidenbinder, C. Torregrosa
CERN, Meyrin, Switzerland
- P. Simon
TU Darmstadt, Darmstadt, Germany
|
|
|
The beam stored energy and the peak intensity of CERN Large Hadron Collider (LHC) will grow in the next few years. The former will increase from the 320 MJ values of Run2 (2015-2018) to almost 540 MJ during Run3 (2022 onwards) and 680 MJ during the HL-LHC era putting stringent requirements on beam intercepting devices, such as absorbers and dumps. The HiRadMat-56-HED (High-Energy Dumps) experiment performed in Autumn 2021 executed at CERN HiRadMat facility employed the Super Proton Synchrotron accelerator (SPS) 440 GeV/c proton beam to impact different low-density carbon-based materials targets to assess their performance to these higher energy beam conditions. The study focused on advanced grades of graphitic materials, including isostatic graphite, carbon-fiber reinforced carbon and carbon-SiC materials in addition to flexible expanded graphite. Some of them specifically tailored in collaboration with industry to very specific properties. The objectives of this experiment are: (i) to assess the performance of existing and potentially suitable advanced materials for the currently operating LHC beam dumps and (ii) to study alternative materials for the HL-LHC main dump or for the Future Circular Collider dump systems. The contribution will detail the R&D phase during design, the execution of the experiment, the pre-irradiation tests as well as the first post irradiation examination of the target materials. Lessons learnt and impact on operational devices will also be drawn.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2022-THPOTK049
|
|
About • |
Received ※ 03 June 2022 — Revised ※ 15 June 2022 — Accepted ※ 16 June 2022 — Issue date ※ 04 July 2022 |
Cite • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|
THPOTK052 |
Muon Collider Graphite Target Studies and Demonstrator Layout Possibilities at CERN |
2895 |
|
- F.J. Saura Esteban, M. Calviani, D. Calzolari, R. Franqueira Ximenes, A.M. Krainer, A. Lechner, R. Losito, D. Schulte
CERN, Meyrin, Switzerland
- C.T. Rogers
STFC/RAL/ISIS, Chilton, Didcot, Oxon, United Kingdom
|
|
|
Muon colliders offer enormous potential for research of the particle physics frontier. Leptons can be accelerated without suffering large synchrotron radiation losses. The International Muon Collider Collaboration is considering 3 and 10 TeV (CM) machines for a conceptual stage. In the core of the Muon Collider facility lays a MW class production target, which will absorb a high power (1 and 3 MW) proton beam to produce muons via pion decay. The target must withstand high dynamic thermal loads induced by 2 ns pulses at 5-50 Hz. Also, operational reliability must be guaranteed to reduce target exchanges to a minimum. Several technologies for these systems are being studied in different laboratories. We present in this paper the results of a preliminary feasibility study of a graphite-based target, and the different layouts under study for a demonstrator target complex at CERN. Synergies with advanced nuclear systems are being explored for the development of a liquid metal target.
|
|
DOI • |
reference for this paper
※ https://doi.org/10.18429/JACoW-IPAC2022-THPOTK052
|
|
About • |
Received ※ 07 June 2022 — Revised ※ 14 June 2022 — Accepted ※ 16 June 2022 — Issue date ※ 18 June 2022 |
Cite • |
reference for this paper using
※ BibTeX,
※ LaTeX,
※ Text/Word,
※ RIS,
※ EndNote (xml)
|
|
|